x

gianni gianno

Forum Replies Created

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • September 30, 2014 at 2:50 pm in reply to: connect turntable to Boss DD 7 #2065521
    gianni gianno
    Participant

    the specifications of the DD7 are thesE

    Specifications

    Controls: E.Level, F.Back, D.Time, 4-way Mode switch
    Connectors: Input, Output, Direct Out, AC Adaptor
    Current Draw: 55 mA (DC 9V, D.Time control at center)
    Weight: 450 g (0.99 lb.)
    A/D Conversion: 12-bit logarithmic compression
    D/A Conversion: 12-bit logarithmic compression
    Input Impedance: 1Mohm (FET Input)
    Residual Noise Level: -95dBm (IHF-A)
    Recommended Load Impedance: 10kOhm or greater
    Delay Time: 12.5 to 800ms
    Recommended AC Adaptor: PSA Series

    September 30, 2014 at 2:01 pm in reply to: connect turntable to Boss DD 7 #2065471
    gianni gianno
    Participant

    yes sorry. I will not publish further quetions if they are the same.

    I saw that the DD7 is usually connected to XONE 92 mixer.

    that`s why i asked 🙂

    September 30, 2014 at 9:24 am in reply to: connect turntable to Boss DD 7 #2065251
    gianni gianno
    Participant

    the interface of the mixer is this http://www.123dj.com/mixers/pioneer/djmt1back.jpg

    September 30, 2014 at 9:22 am in reply to: connect turntable to Boss DD 7 #2065231
    gianni gianno
    Participant

    Thank you very much.

    Do you confirm that i can connect the delay pedal using cable converters?

    How do you suggest? I was wondering if i can connect the delay to the master out of the mixer, or directly to turntable. How it will work in your opinion ?

    thank yoy veru much 🙂

    September 25, 2014 at 9:33 am in reply to: connect turntable to Boss DD 7 #2063281
    gianni gianno
    Participant

    no, when i switch to phono, the channel works just as a normal mixer channel, without effect. Unfortunally the effects work only if the channel is in USB mode or in timecode mode, but i dont like timecode, i like to use my original vinyls. That`s why i wanted to connect the turntable to effect station and then the effect station to the channel of the mixer.

    What do you think about the RMX 500 effect station?

    Also, the turntable looks to have only phono cable, what happen is i put a little converter in order to have line and then put it in effect station and then the effect station to channel 1 on mixer?

    thanks

    September 25, 2014 at 8:59 am in reply to: connect turntable to Boss DD 7 #2063231
    gianni gianno
    Participant

    thanks again, very clear 🙂

    just for information: my mixer is a traktor certified, it has 2 channels that can work in 3 modes (phono, line and usb). When i use them in usb mode i have tracks from the computer and have automatically effects from traktor. Right now i`m using channel 1 in phono mode (using my turntable) and channel 2 in USB mode. I just would like to have some effects also on the turntable.

    so, is there any way> ? it has one rca cable going out and one hole for “remote control” (it says)

    thanks 🙂

    September 24, 2014 at 10:34 pm in reply to: connect turntable to Boss DD 7 #2062861
    gianni gianno
    Participant

    thank you very much for the answer, but what happens if i connect the turntable to the input of the boss dd7 and the dd7 output in the input channel one of the mixer ?

    September 24, 2014 at 2:52 pm in reply to: connect turntable to Boss DD 7 #2062461
    gianni gianno
    Participant

    if you have other solutions in order to have effects with the turntable i appreciate 🙂

  • Author
    Posts
Viewing 8 posts - 1 through 8 (of 8 total)